HAZARD ANALYSIS

STEP SEQUENCE OF JOB PROCEDURES	POTENTIAL HAZARDS (SPECIFIC)	ACTIONS TO REDUCE/ELIMINATE HAZARDS
● TRANSPORT CASING RUNNING TOOLS AND TORQUE MONITORING EQUIPMENT TO RIG FLOOR	● EQUIPMENT/TOOLS COULD BE DROPPED DOWN THE RIG STAIRS WHILE CARRYING BYHAND TO THE RIG FLOOR ● EQUIPMENT COULD FALL DOWN THE V-DOOR FROM STRAPS NOT PROPERLY RATED FOR WEIGHT, WORN OUT, OR NOT PROPERLY SECURED WHILE HOISTED TO THE RIG FLOOR	● LOAD EQUIPMENT OR TOOLS INTO A BACKPACK TO TRANPSORT BY HAND UP THE RIG STAIRS ● ALWAYS MAINTAIN 3 POINTS OF CONTACT WHILE GOING UP AND DOWN RIG STAIRS ● DOUBLE CHECK THE CONDITION OF HOIST STRAPS, THEIR RATING, AND THAT THEY ARE SECURED TO EQUIPMENT BEFORE LIFTING TO RIG FLOOR.>● NEVER STAND UNDER OR IN THE LINE OF FIRE OF SUSPENDED LOADS GOING UP OR DOWN THE V-DOOR
● CONDUCT A PREJOB SAFETY MEETING TO DISCUSS EQUIPMENT RIG UP, TALLY DETAILS, AND HANDLING/PROCEDURES OF CASING RUN		● REVIEW JSA WITH ALL PERSONNEL AND COMPANY REP THEN SIGN OFF ON SAFETY MEETING SHEET ● GIVE ALL PERSONNEL A CHANCE TO ADD COMMENTS, CONCERNS, OR GUIDELINES TO ALL SAFETY REQUIREMENTS AND PROCEDURES ● MAKE ADJUSTMENTS OR ADDITIONS TO JSA AT THE END OF THE TSI JSA DOCUMENT &$9679; CONDUCT A JSA WHEN NEW RIG CREW BEGINS WORK
● RIG UP CASING CREW AND TORQUE MONITORING EQUIPMENT	● EQUIPMENT TAILED IN COULD SWING INTO OTHER EQUIPMENT OR PERSONNEL	● NEVER TURN YOUR BACK TO LOADS BEING TAILED IN AND STAND CLEAR UNTIL THE LOAD IS POSITIONED
● STRING ACCESSORIES BROUGHT UP TO RIG FLOOR	● HANDS AND FEET COULD BE INJURED WHILE RIGGING UP EQUIPMENT ● TRIPS AND FALLS FROM POTENTIAL HAZARDS AS EQUIPMENT GETS ORGANIZED AND INTO CORRECT POSITION	● KEEP CABLES FROM EQUIPMENT ORGANIZED AND OUT OF THE WAY TO PREVENT DAMAGES OR TRIP HAZARDS ● ALWAYS WEAR GLOVES AND BE MINDFUL OF YOUR HAND AND FEET PLACEMENT WHILE WORKING ● KEEP AREA AS CLEAR AS POSSIBLE FROM TRIP HAZARDS IN THE EVENT YOU NEED TO EVACUATE THE RIG FLOOR IMMEDIATELY
● WELL CONTROL ON THE RIG FLOOR	● NOT HAVING WELL CONTROL ON THE RIG FLOOR COULD BE THE DIFFERENCE IN CONTROLLING THE WELL OR NOT	● BEFORE THE CASING RUN BEGINS, HAVE ALL WELL CONTROL EQUIPMENT ON THE RIG FLOOR, READY TO BE INSTALLED ● IN THE PREJOB MEETING, GO OVER THE ACTIONS AND WELL CONTROL EQUIPMENT IN THE EVENT SECURING THE WELL IS NEEDED
● RUNNIG CASING/TUBING	● CONTROL OF THE INCOMING JOINT COULD BE LOST WHICH COULD SWING IN, STRIKING PERSONNEL ● YOU COULD BE CAUGHT BETWEEN EQUIPMENT OR PIPE AND THE DERRICK LEG OR OTHER EQUIPMENT IF NOT PAYING ATTENTION	● ALWAYS FACE THE WORK AND NEVER LET THE JOINT OF CASING OUT OF YOUR SIGHT WHLE JOINTS ARE TAILED IN ● MAKE SURE YOU STAND TO THE SIDE OF THE CASING AND ALWAYS HAVE AN ESCAPE ROUTE ● NEVER STAND BETWEEN EQUIPMENT AND THE DERRICK LEG OR OTHER EQUIPMENT SO YOU ARE NOT CAUGHT BETWEEN THE TWO AND INJURED ● DO NOT DISTRACT WORKING PERSONNEL ON THE RIG FLOOR
● V-DOOR OPERATORS	● NOT HAVING A PERSON OR HAVING MORE THAN ONE PERSON FLAGGING IN THE OPERATORS COULD INJURE OTHERS BY CREATING CONFUSION	● ONLY ONE PERSON SHOULD BE DESIGNATED AS THE FLAGGER FOR THE OPERATION AND SHOULD WEAR THE DESIGNATED VEST IF REQUIRED ● USE HAND SIGNALS TO COMMUNICATE WITH OPERATORS TO CLEARLY UNDERSTAND INSTRUCTIONS